background image

 

 

 

Algas-SDI Operation and Maintenance Manual 

– P/N – 52642

 

3-13

 

 

 

Operation 

 

Direct Fired Vaporizer start up procedure 

1.  Before  starting  the  vaporizer,  close  the  outlet  valve  in  the  vapor  service 

line. 

2.  Fill  the  vaporizer  with  LP  gas  liquid  by  slowly  opening  the  liquid  supply 

line  valve  between  the  storage  tank  and  the  vaporizer.    If  this  valve  is 
opened too quickly, the excess flow valve  in the tank may close.   If this 
occurs, close the liquid supply line valve and allow the excess flow valve 
to equalize and re-open. 

3.  If  the  vaporizer  is  installed  with  a  separate  burner  supply  line  not 

connected to the vaporizer (

see page 2-8

), open the valve supplying gas 

to the burner supply regulator. 

4.  Turn  the  temperature  control  dial  on  the  thermostatic  gas  control  valve 

counterclockwise  to  the  "RUN"  position.   

“RUN”  position  indicates  that 

the pilot and main burner can start operating.  

Figure 7

 

 

Temperature control 

dial in “RUN” position 

 

5.  Turn  the  re

igniter  switch  to  “ON”  and  press  the  pilot  button  down  (see 

Figure  8).      Continue  to  hold  the  pilot  button  for  30  to  60  seconds  and 
release.  Pilot should remain lit. 

 

NOTE:

  If  the  ambient  temperature  is  below  10°F  (-12°C)  when  the  pilot 

button  is  released  it  is  likely  that  the  main  burner  will  immediately  cycle  on. 
As  soon  as  the  LP  gas  inside  the  heat  exchanger  heats  up  above  this 
temperature  the  main  burner  will  cycle  off.  This  is  normal  operation  for  the 
thermostatic gas valve. 

 

 

 

Содержание Direct Fired 120/60H

























































Отзывы: