Alcatel-Lucent OmniAccess AP60 Скачать руководство пользователя

Страница: 7 / 68

Introduction

Chapter 1

Antenna fixtures for Wireless Communications

Depending on the model, the AP will have one of the following:

OmniAccess AP60–Two Reverse Polarity SMA (RP-SMA) connectors for
attaching separate antennas (not included). For details, see

“OmniAccess AP60

Detachable Antennas”

page 26

. (The AP60 requires that both connectors be

used in AOS-W 2.2 releases or lower. Single antenna operation is supported
with AOS-W 2.3 or higher.)

OTE

—

When facing the AP60 as shown in

Figure 1-1

, the antenna connector on the

right is for antenna 1, and the connector on the left is for antenna 2 in a diversity
configuration.

OmniAccess AP61–Built-in swivel array with dual, tri-band, omnidirectional
antennas

Indicator LEDs

During operation, the OmniAccess AP60/61 LEDs provide the following
information:

OTE

—

LEDs on the Wireless LAN Switch provide additional status and secu-

rity information about connected APs.See the

Alcatel AOS-W User Guide

for

more information.

ABLE

1-1

OmniAccess AP60/61 LEDs

LED

State

Description

PWR

Off

The device is off - no power.

Green-Solid

The device is powered and operating.

ENET

Off

No link on the FE port. No connection to the
network.

Green-Solid

Ethernet link detected on the FE port.

Green-Flashin
g

Transmitting or receiving data across the FE
port. Flashing rate is proportional to network
activity.

Wireles
s LAN

Off

The wireless interface is disabled or down.

Green-Solid

The wireless interface is enabled and
functioning as an Access Point.

Green-Flashin
g

The wireless interface is enabled and
functioning as an Air Monitor.

Содержание OmniAccess AP60





































































Результаты поиска

Содержание OmniAccess AP60

Отзывы:

Похожие инструкции для OmniAccess AP60

Бренды по названию

Популярные бренды

Alcatel-Lucent OmniAccess AP60, Руководство по установке

Результаты поиска

Содержание OmniAccess AP60

Отзывы:

Похожие инструкции для OmniAccess AP60

Бренды по названию

Популярные бренды