Alcatel-Lucent OmniAccess AP60 Скачать руководство пользователя

Страница: 44 / 68

OmniAccess AP60/61: Installation Guide

Part 031643-00 Rev. 01

June 2005

When prompted, log in to the Wireless LAN Switch as the administrator:

This will present you with the Wireless LAN Switch SOE console prompt:

Connect to the Wireless LAN Switch port to which the OmniAccess
AP60/61 is physically attached:

where

slot number

is the physical slot of the line card in the Wireless LAN switch,

and

port number

is the physical port.

If the AP has not finished booting, allow the Autoboot timer to expire. When
the device has booted, the AP support prompt (

) will appear.

Direct Terminal Connection

This method requires that the OmniAccess AP60/61 is connected to a
compatible serial console using the Alcatel serial breakout adapter (see

“Connecting the Console Terminal”

page 16

1. Set up your local terminal.

This procedure requires a terminal or computer running terminal emulation
software with the following settings:

Establish console communication.

Press <Enter> a few times to establish communication between the
OmniAccess AP60/61 and terminal.

If the AP has not finished booting, allow the Autoboot timer to expire. When
the device has booted, the AP Support prompt (

) will appear.

user:

admin

password:

<administrator password (not displayed)>

Available commands:
baud [9600|19200|38400|57600|115200]
connect <slot/port>
exit (no args)
soe>

soe>

connect

<slot number>

<port number>

ABLE

3-2

Console Terminal Settings

Baud Rate

Data Bits

Parity

Stop Bits

Flow Control

9600

None

Содержание OmniAccess AP60





































































Результаты поиска

Содержание OmniAccess AP60

Отзывы:

Похожие инструкции для OmniAccess AP60

Бренды по названию

Популярные бренды

Alcatel-Lucent OmniAccess AP60, Руководство по установке

Результаты поиска

Содержание OmniAccess AP60

Отзывы:

Похожие инструкции для OmniAccess AP60

Бренды по названию

Популярные бренды