Albixon Inverboost C Скачать руководство пользователя страница 26

Страница: 26 / 36

/ Swimming Pool Heat Pump Inverboost C

Malfunction

Error code

Reason

Solution

VDC voltage too
high protection

EE10

1. Line voltage is too high
2. Driver board is damaged.

1. Check whether the power

supply is normal

2. Change driver board or main

board

IPM module
protection

EE11

1. Data mistake
2. Wrong compressor phase

connection

3. Compressor liquid and oil

accumulation lead to the
current becomes larger

4. Poor heat dissipation

of drive module or high
ambient temperature

5. Compressor or driver

board damaged

1. Program error, turn off

electricity supply and restart
after 3 minutes

2. Check compressor sequence

connection

3. Check the pressure of system

by pressure gauge

4. Check if the ambient and

water temperature is over high

5. If it is the refrigration system

failure, send it to the service
center

6. Change driver board

VDC voltage too low
protection

EE12

1. Mother line voltage is too

low

2. Driver board is damaged.

1. Check if the power is in the

normal range

2. Change driver board

Input current over
high protection.

EE13

1. The compressor current is

too large momentary

2. The water flow is abnormal
3. Power fluctuations within a

short time

4. Wrong reactor

1. Check the compressor if it

works normally

2. Check the waterway system
3. Check if the power is in the

normal range

4. Check if the reactor is used

correctly.

IPM module thermal
circuit is abnormal

EE14

1. Output abnormity of IPM

module thermal circuit

2. Fan motor is abnormal or

damaged

3. Fan blade is broken

1. Check if the motor speed

is too low or fan motor is
damaged, replace it by a new
one.

2. Replace a new driver board
3. Change the fan blade if it is

broken

IPM module
temperature too
high protection

EE15

1. Output exception of IPM

module thermal circuit

2. Fan motor is abnormal or

damaged

3. Fan blade is broken
4. The screw on driver board

is loose

1. Check the main board or

replace the driver board

2. Check if the motor speed

is too low or fan motor is
damaged, replace it by a new
one if any failure.

3. Change the fan blade if it is

broken

4. Check the screw on driver

board

Содержание Inverboost C





































Результаты поиска

Содержание Inverboost C

Отзывы:

Похожие инструкции для Inverboost C

Бренды по названию

Популярные бренды

Albixon Inverboost C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Inverboost C

Отзывы:

Похожие инструкции для Inverboost C

Бренды по названию

Популярные бренды