Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 18

Страница: 18 / 230

SAFETY

RMB 1660 01/22

Safety Section 1-8

SAFETY

RUN OVER HAZARDS

TO AVOID DEATH OR SERIOUS INJURY FROM FALLING OFF TRACTOR OR
EQUIPMENT RUN OVER:

•

USE ROPS

and

SEAT BELT

equipped tractors for mowing operations.

•

KEEP ROPS

locked in

position.

•

ONLY

start tractor while seated in tractor seat.

•

ALWAYS BUCKLE UP

seat belt when operating tractor and equipment.

•

ONLY OPERATE

tractor and equipment while seated in tractor seat.

•

NEVER ALLOW RIDERS

on tractor or implement.

•

When not mowing stow Boom and Mower head in transport location before moving.

WHEN MOUNTING AND DISMOUNTING TRACTOR:

•

ONLY

mount or dismount when tractor and moving parts are stopped

•

STOP ENGINE AND PTO,

engage parking brake, lower implement, allow all moving parts to stop and

remove key before dismounting from tractor.

PN ROBM-01

Содержание BUSH HOG RMB 1660







































































































































































































































Результаты поиска

Содержание BUSH HOG RMB 1660

Отзывы:

Бренды по названию

Популярные бренды

Alamo BUSH HOG RMB 1660, Руководство оператора

Результаты поиска

Содержание BUSH HOG RMB 1660

Отзывы:

Бренды по названию

Популярные бренды