manualshive.com logo in svg

Alamo BUSH HOG RMB 1660, Руководство оператора

Поделиться
Скачать
Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 159

OPERATION

RMB 1660   01/22

Operation Section 4-37

© 2022 Alamo Group Inc.

OPERA

T

ION

14.7 Shutting Down the Attached Head

To shut down attached mower head, first bring the
tractor to a complete stop. Decrease engine RPM
to idle then disengage cutterhead. The mower head
will come to a complete stop within a suitable
amount of time. Do not engage or disengage the
cutterheads at a high RPM unless there is an
emergency situation.

Park the tractor on a level surface, place the
transmission in park or neutral and apply the
parking brake, shut down the engine, remove the
key, and wait for all motion to come to a complete
stop before exiting the tractor.

    OPS-B- 0011_G

BEFORE leaving the tractor seat, lower the implement, set the parking
brake and/or set the tractor transmission in parking gear, disengage the
PTO, stop the engine, remove the key, and wait for all moving parts to
stop. Place the tractor shift lever into a low range or parking gear to
prevent the tractor from rolling. Never dismount a Tractor that is moving
or while the engine is running. Operate the Tractor controls from the
tractor seat only.

  (SG-9)

Always shut the Tractor completely down, place the transmission in park, and set the

parking brake before you or anyone else attempts to connect or disconnect the Implement

and Tractor hitches. 

 

(S3PT-15)

Never allow children or other persons to ride on the Tractor or Implement.
Falling off can result in serious injury or death.  

(SG-10)

Содержание BUSH HOG RMB 1660







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды