Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 168

Страница: 168 / 230

OPERATION

RMB 1660 01/22

Operation Section 4-46

OPERA

ION

Problem

Possible Cause Remedy

Cylinder Excessive
Drift

May be normal Operation

Check Allowable Drift rates in Service Manual

Cylinder Piston Seals
Bypass

Test to confirm and repair or replace

Damaged or Defective
Work Port Relief Valves

Check Relief Pressures. Repair or replace as
required

Oil Contamination

May be root cause of any internal Leakage.
Test oil and replace as required.

Related to Issues
described in Previous
section: Boom moves
under its own power

Review the previous section

Cylinder Leaks at
Fittings

Loose Fittings

Check for cracks and retighten

Wrong Fittings Installed

Replace with Correct fittings

Damaged or defective
fitting (cracked)

due to over tightening, replace hose or fitting

Fitting Port cracked

Repair or replace Cylinder or port

Cylinder Leaks at Rod

Faulty Seals on Cylinder
Gland

Disassemble and Replace

Damaged Cylinder Rods

Clean or Replace the Rod as required.

Cylinder Rods Bent

Determine Cause of Overload. Replace the
Rod

Cylinder Moves Wrong
Way (Not the function
that was actuated)

Incorrect Hose Routing

Wire Harness improperly
installed

Check Hose Diagram in the Service Manual
and route the hoses correctly

Confirm incorrect placement and re-attach the
harness connectors as needed

Operator Perception of
Correct Operation is
incorrect

Consult the Operator's Manual for Correct
operation and communicate with the Operator.

Cylinder Moves
intermittent (all
functions)

Cylinder Control Pump
Failure (All functions
affected)
Load Sense Signal Not
reaching the pump.
Low Or Improper Oil in
Hydraulic system

Test pump to confirm. Rebuild or replace as
required.

Check valve Pilot pressure and load sense
Check valves.
Replace or fill as required.

Contamination of Oil
causing restricted flow in
the valve.
No voltage to Joystick
Controller
Faulty Joystick Controller

Replace oil, and clean components.

Check Fuses, wires etc and repair as required.

Test then replace or repair as required.

Содержание BUSH HOG RMB 1660







































































































































































































































Результаты поиска

Содержание BUSH HOG RMB 1660

Отзывы:

Бренды по названию

Популярные бренды

Alamo BUSH HOG RMB 1660, Руководство оператора

Результаты поиска

Содержание BUSH HOG RMB 1660

Отзывы:

Бренды по названию

Популярные бренды