manualshive.com logo in svg

Alamo BUSH HOG RMB 1660, Руководство оператора

Поделиться
Скачать
Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 151

OPERATION

RMB 1660   01/22

Operation Section 4-29

© 2022 Alamo Group Inc.

OPERA

T

ION

13.1 Starting the Tractor

The procedure to start the tractor is model specific.
Refer to the tractor operator’s manual for starting
procedures for your particular tractor.  Consult an
authorized dealer if the starting procedure is
unclear.  Ensure the 3-point control lever is in the
lowered position and the PTO is disengaged before
starting the tractor.  

OPS-U-0033

13.2 Brake and Differential Lock Setting

Make sure the tractor brakes are in good operating
condition. Tractor brakes can be set to operate
independently allowing single rear wheel braking
action or locked together to provide simultaneous
rear wheel braking.  FOR MOST DRIVING AND
OPERATING CONDITIONS, THE BRAKE PEDALS
SHOULD BE LOCKED TOGETHER TO PROVIDE
THE MOST EFFECTIVE BRAKING ACTION. 

Always disengage the tractor differential lock when
turning. When engaged the differential lock will
prevent or limit the tractor from turning. During
normal conditions, locking the differential provides
no benefit and should not be used.  

OPS-U- 0013

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes.
When operating down a hill or on wet or rain slick roads, the braking distance increases; use
extreme care and reduce your speed in these conditions. When operating in traffic, always
use the Tractor’s flashing warning lights and reduce your speed.   Be aware of traffic around
you and watch out for the other guy.

Содержание BUSH HOG RMB 1660







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды