manualshive.com logo in svg

Alamo BUSH HOG RMB 1660, Руководство оператора

Поделиться
Скачать
Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 124

OPERATION

RMB 1660   01/22

Operation Section 4-2

© 2022 Alamo Group Inc.

OPERA

T

ION

Bush Hog RMB 1660 BOOM MOWER 

OPERATING INSTRUCTIONS

Bush Hog Boom Mowers are manufactured with quality material by skilled workers. These mowers are
designed for cutting grass and small weeds. The mower is equipped with protective deflectors to prevent
objects being thrown from the mower by the blades, however, no shielding is 100% effective. All shields,
guards, and deflectors equipped on the mower must be maintained in good operational condition.

It is the operator’s responsibility to be knowledgeable of all potential operating hazards and to take every
reasonable precaution to ensure oneself, others, animals, and property are not injured or damaged by the
mower, tractor, or a thrown object. Do not operate the mower if passersby, pets, livestock, or property are
within 300 feet of the unit.

•

All THROWN OBJECT SHIELDING

 including, Front and Rear Deflectors and Skid Shoes are in place and

in good condition when mowing. 

•

Mower is adjusted to be close and parallel to ground without exposing blades.

•

MOWING AREA

 has been inspected and foreign materials and debris have been removed.

•

PASSERSBY

 are inside enclosed vehicle.

This section of the Operator’s Manual is designed to familiarize, instruct, and educate safe and proper mower
use to the operator. Pictures contained in this section are intended to be used as a visual aid to assist in
explaining the operation of a boom mower and are not specific to any model. Some pictures may show shields
removed for picture clarity. NEVER operate implement without all shields in place and in good operational
condition. The operator must be familiar with the mower and tractor and all associated safety   practices before
operating the mower and tractor. Proper operation of the mower, as detailed in this manual, will help ensure
years of safe and satisfactory use of the mower.

IMPORTANT:

 To avoid mower damage, retorque all bolts after the first 10 hours of operation. Refer to the

Torque Chart at the end of the Maintenance Section to ensure bolts are properly tightened.

Standard Equipment and Specifications

READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS
MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND
IMPLEMENT.  

If you do not understand any of the instructions, contact your nearest authorized dealer for a

full explanation.  Pay close attention to all safety signs and safety messages contained in this manual and
those affixed to the implement and tractor.  

OPS-U- 0001

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Death or serious
injury may occur unless care is taken to follow the warnings and instructions stated in the
Safety Messages. Always use good common sense to avoid hazards. 

(SG-2)   

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las
medidas de seguridad.

 (SG-3)

Содержание BUSH HOG RMB 1660







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды