Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 136 | Manualshive

Страница: 136 / 230

Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 136

OPERATION

RMB 1660 01/22

Operation Section 4-14

© 2022 Alamo Group Inc.

OPERA

T

ION

Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement.
Place the Mower Head on the ground or securely supported on blocks or stands, disengage

the PTO, and turn off the engine. Push and pull the control Levers or Joystick several times
to relieve pressure prior to starting any maintenance or repair work.

(SBM-6)

Never leave the mower unattended while the head is in the raised
position. The mower could fall causing serious injury to anyone who
might inadvertently be under the mower

(SBM-4)

Do not operate this Equipment with hydraulic oil or fuel leaking. Oil
and fuel are explosive and their presence could present a hazard. Do
not check for leaks with your hand! High-pressure oil streams from
breaks in the line could penetrate the skin and cause tissue damage
including gangrene. To check for a hose leak, SHUT the unit ENGINE
OFF and remove all hydraulic pressure. Wear oil impenetrable gloves,
safety glasses and use cardboard to check for evidence of oil leaks. If
you suspect a leak, REMOVE the HOSE and have it tested at a Dealer.
If oil does penetrate the skin, have the injury treated immediately by a
physician knowledgeable and skilled in this procedure.

(SG-15)

HYDRAULIC PUMP/OIL RESERVOIR

•

Check oil reservoir level and oil condition. (Add
specific type oil if low.)

•

Change hydraulic oil filter and hydraulic oil
according to maintenance schedule.

•

Ensure there are no oil leaks and fitting are
properly connected.

•

Inspect overall condition of hydraulic pump.

•

Inspect pump drive shaft.

Check the fluid level in the Hydraulic Tank on the Tractor, and add oil if required.  As the air has been forced out
of the Cylinders and Hoses, it goes into the Hydraulic Tank and reduces the volume of oil.  Maintain the oil level
within the sight gauge located on the side of the resevoir. Never fill the tank above the sight gauge to allow for
the expansion of the oil.  The tank maintains pressure after the mower has been run. Stand off to one side
when removing the breather cap element to prevent possible injury. To relieve pressure remove the breather
cap element and depress the spring loaded pressure valve to release any excess air.

OPS-B- 0024_H

«
...
134
135
136
137
138
...
»

Содержание BUSH HOG RMB 1660







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды