Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 174 | Manualshive

Страница: 174 / 230

Alamo BUSH HOG RMB 1660 Скачать руководство пользователя страница 174

OPERATION

RMB 1660 01/22

Operation Section 4-52

© 2022 Alamo Group Inc.

OPERA

T

ION

Problem

Possible Cause

Remedy

Spindle Locks Up
(Seizes and Won't Turn)

Loss of lubrication in
spindle

Indicated by catastrophic failure of the upper
bearing. See the previous section

Excessive bearing pre-
load

Disassemble the spindle and inspect the
bearings for wear. Re-assemble following the
bearing pre-load specifications in the Technical
Service Manual.

Blade bar bolts too long

Installing the incorrect bolts (too long) for the
blade carrier will allow the bolts to contact the
lower bearing and will lock up the spindle.
Install the correct bolts.

Interference due to bent
seal protector

Inspect the seal guard ring (welded to the blade
carrier or bar) Replace or repair as needed.

Starter on Tractor Won't
Crank

Wire harness incorrectly
installed

Check harness attachment to the ignition
switch and to the battery. Also, check for
proper ground.

Tractor Battery Dead or
Low (Continuous Power
Draining)

On/Off switch malfunction

Inspect to ensure power to switch is interrupted
when the switch is in the off position

Short to ground in wire
harness

Inspect for damage or heat stress to the
harness. Check for shorted wires or melted
insulation. Check proper connection to the
ignition switch and battery.

Battery failure

Test the battery and replace per the tractor
manufacturers recommendation

Tractor issues

Follow tractor manufacturer recommendations
for troubleshooting electrical problems with the
tractor.

«
...
172
173
174
175
176
...
»

Содержание BUSH HOG RMB 1660







































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды