AJA Io IP Скачать руководство пользователя страница 8

Страница: 8 / 86

Io IP Transport, Capture, Display v16.2r1 8

www.aja.com

Drivers

AJA device drivers for the host system OS provide tightly integrated hardware/

software operation.

AJA Control Panel

The Control Panel provides:

• Source selection and control of your AJA hardware
• A block diagram to show visually what routing and processing is being

performed

AJA Control Room

Control Room is a cross-platform software application for ingest, playback and

output with AJA products.

AJA System Test

AJA System Test provides accurate and detailed evaluations of drive and system

performance statistics, allowing you to measure the capabilities of your system

for recording and playing back various resolutions and codecs. The application

includes:

•  System Disk Test
•  AJA Device Test
•  System Report

The application tests Read and Write, Capture and Playback speeds in both

Megabytes per second and Frames per second. The disk speed tests differ from

standard disk I/O performance applications in that they specifically test the

system under conditions typically encountered with video capture, playback, and

editing.

NOTE: Theoretically the best test (or simulation) is to fill your storage disk to 80% and

then test capture at the highest data rate you will use.

3rd-Party Plug-ins

Plugins for popular 3rd-party Professional Video Applications from Adobe, Avid,

Apple, OBS and Telestream.

NMOS App

Available for automatic discovery of IP devices.

Network Requirements

For uncompressed workflows (SMPTE ST 2022-6 and SMPTE ST 2110) a 10GbE

switch is required.
For SMPTE ST 2110 specifically, a PTP clock source must also be deployed and the

switch must therefore also be PTP aware.
In all cases the switch used must be both managed (configurable) and IGMP

aware.
SFPs are not included with the purchase of Io IP. Recommended SFPs are listed in

"Specifications" on page 71

Содержание Io IP























































































Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды

AJA Io IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды