AJA Io IP Скачать руководство пользователя страница 56

Страница: 56 / 86

Io IP Transport, Capture, Display v16.2r1 56 www.aja.com

The s2110 Status screen reports various network statuses, including IP addresses

and PTP operation. It also permits access to IP configuration options.

SFP1 Local IP

The Local IP address of the top SFP is displayed. The current transmit and receive

bitrates are also reported, in Gb/sec.

SFP2 Local IP

Same as above, but for the lower SFP module, if installed.

PTP Information

The PTP Grandmaster and Master IDs are displayed, as well as the current PTP

Status.

Advanced Button

Clicking on the Advanced button takes you to the 2110 IP configuration windows.

See

"IP Config Editor Window" on page 59

for more information.

IP Config Capture Tab

The Capture Tab screen shows the current settings for receiving IP streams, the

status of that stream, and allows activating and deactivating each stream.

Session Description Protocol (SDP) information, used for easy configuration, can

also be loaded and refreshed from this screen.

Содержание Io IP























































































Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды

AJA Io IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды