background image

Io IP Transport, Capture, Display v16.2r1 2 

www.aja.com

 

Notices

Trademarks

AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc. 

for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for 

use with recorder, router, software and camera products. Because it matters.™ is a 

trademark of AJA Video Systems, Inc. for use with camera products.
Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered trademarks of 

AJA Video Systems, Inc. 
AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, V2Analog™ and 

V2Digital™ are trademarks of AJA Video Systems, Inc.
All other trademarks are the property of their respective owners.

Copyright

Copyright © 2022 AJA Video Systems, Inc. All rights reserved. All information in 

this manual is subject to change without notice. No part of the document may be 

reproduced or transmitted in any form, or by any means, electronic or mechanical, 

including photocopying or recording, without the express written permission of AJA 

Video Systems, Inc.

Contacting AJA Support

When calling for support, have all information at hand prior to calling. To contact AJA 

for sales or support, use any of the following methods:

Telephone

+1.530.271.3190

FAX

+1.530.271.3140

Web

https://www.aja.com

Support Email

[email protected]

Sales Email

[email protected]

Содержание Io IP























































































Отзывы: