AJA Io IP Скачать руководство пользователя страница 57

Страница: 57 / 86

Io IP Transport, Capture, Display v16.2r1 57 www.aja.com

Channel 1-4

Click on the box to enable the configured stream (check mark). Activity of that

stream is indicated by the color of the dot: blue = active, red = inactive.
Clicking on the triangles display information for that video or audio playback

stream.

SDP

The current SDP information is displayed for that stream.

Refresh

Click

Refresh

to update the configuration information. Use when the source

frame rate has changed.

Set

Click

Set

to open a dialog box allowing you to enter SDP configuration

information for the source of the desired stream.

• Select

URL

to enter the text of a network location where the desired SDP

information resides. This can be a URL of a Io IP transmit device.

NOTE: When using a URL for configuration, you need to turn Control Panel's "Follow

Input" setting On and use Refresh if the incoming signal format changes.

• Select

SDP File

to browse to a location with the desired SDP source stream

information. The location selected must point to an SDP file that was created

by the source that is transmitting the signal.

NOTE: When using an SDP for configuration, you need to turn Control Panel's "Follow

Input" setting On and if the incoming signal format changes you will need to

generate and import a new SDP file to accommodate the format change.

Содержание Io IP























































































Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды

AJA Io IP, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io IP

Отзывы:

Похожие инструкции для Io IP

Бренды по названию

Популярные бренды