AJA Io IP Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 86

background image

Io IP Transport, Capture, Display v16.2r1 72 www.aja.com

Video Output IP

• SMPTE ST 2110, 2022-6

• RGB 4:4:4 12-bit, YCbCr 4:2:2 10-bit
• Single channel* output available when using ST 2110 or ST 2022-6 to

transmit 2K/HD

• 4-channels output available when using ST 2110-23 to transmit 4K/

UltraHD**

•  ANC support
•  Tx support for ST 2022-7 up to 2K/HD
•  Tx support for Narrow Receivers**

*Capture and simultaneous monitoring is supported up to 2K/HD
**SMPTE ST 2110 only

Video Output Digital

• 3G-SDI, SMPTE 425

• RGB 4:4:4 12-bit*, YCbCr 4:2:2 10-bit
• 2K/HD downsample available when working with 4K/UltraHD via ST 2110-23

• 1.5G-SDI, SMPTE 292M

• Single Link HD-SDI YCbCr 4:2:2 10-bit
• Dual Link RGB 4:4:4 12-bit*, Dual Link YCbCr 4:2:2 10-bit

• 270 Mbps SDI, SMPTE 259M-C

• YCbCr 4:2:2 10-bit, 8-bit

• HDMI v2.0

•  30/36-bits/pixel, RGB or YUV, 6 Gbps per color component
•  4K/UltraHD, 2K/HD and SD
•  2K/HD downsample available when working with 4K/UltraHD via ST 2110-23

*Bit depth support is application dependent. Check with your software

manufacturer for compatibility.

HDR

• SDI: VPID signaling for SDR/HDR Transfer Characteristics, Colorimetry and

Luminance

• HDMI: HDR10 Support - HDR Infoframe metadata, compatible with HDMI 2.0a/

CTA-861.3

• HDMI: HLG Support - compatible with HDMI 2.0b/CTA-861-G

Note: HDR support is application dependent. Check with your software

manufacturer for compatibility.

Audio Input IP

• Up to 16-channel embedded audio, 24-bit per channel, 48 kHz synchronous

Audio Inputs Analog

• 8-channel, 24 and 16-bit A/D analog audio, 48 kHz sample rate, balanced,

using industry standard 8x XLR on DB-25 breakout cable (cable not included)

•  +24 dBu full scale digital (0 dBFS)
•  +/- 0.2 dB 20 to 20 kHz frequency response
•  Input supported across Ch 1-8, Ch 1-4, or Ch 5-8 depending on the chosen

configuration

Audio Output IP

• Up to 16-channel embedded audio, 24-bit per channel, 48 kHz synchronous

«
...
70
71
72
73
74
...
»

Содержание Io IP























































































Отзывы:

Нет отзывов

Похожие инструкции для Io IP

Бренд: JBL Страницы: 16

Authentics L 16

Бренд: JBL Страницы: 17

Бренд: Magnavox Страницы: 24

Бренд: Magnavox Страницы: 22

Бренд: Magnavox Страницы: 21

Magnavox FW 750C

Бренд: Magnavox Страницы: 28

Magnavox FW 2012

Бренд: Magnavox Страницы: 16

MME239 - Micro DVD Home Theater System

Бренд: Magnavox Страницы: 39

Бренд: R. Beck Maschinenbau Страницы: 31

XTS 7IP WH WIFI

Бренд: CAME BPT Страницы: 24

EAGLE-GRIP 4 Series

Бренд: Easy Lift Equipment Страницы: 27

CompuScope 85GC

Бренд: Gage Страницы: 174

3D TRASAR Series

Бренд: Nalco Страницы: 243

IP Force 9151101W

Бренд: 2N Страницы: 118

Бренд: Balluff Страницы: 4

Бренд: Fasttel Страницы: 9

Бренд: Omron Страницы: 154

Бренд: National Instruments Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды