AJA Io IP Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 86

background image

Io IP Transport, Capture, Display v16.2r1 71 www.aja.com

Appendix A – Specifications

Io IP Tech Specs

Video Formats

•  (4K)** 4096 x 2160p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
•  (UltraHD)** 3840 x 2160p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
•  (2K) 2048 x 1080p 23.98, 24, 25, 29.97, 30, 50*, 59.94*, 60*
•  (2K) 2048 x 1080PsF 23.98, 24, 25
•  (HD) 1080p 23.98, 24, 25, 29.97, 30, 50, 59.94, 60
•  (HD) 1080PsF 23.98, 24, 25, 29.97, 30
•  (HD) 1080i 50, 59.94
•  (HD) 720p 50, 59.94, 60
•  (SD) 625i 50
•  (SD) 525i 59.94

*SMPTE ST 2110 only
**2SI over IP via ST 2110-23 only
Note: High Frame Rate capabilities are dependent on host system attributes. Not

all systems and configurations will support all frame rates.

Media Transport Interfaces

• SMPTE ST 2110 (-10, -20, -21, -23, -30, -40), 2022-6

• 2x SFP+ Cages - SFPs not included

• Recommended 10 GigE SFP+ modules:

•  Arista Networks SFP-10G-SR Compatible 10GBASE-SR
•  Fiberstore SFP-10GSR-85 10G SFP+ 850nm
•  Finisar FTLX1471D3BCL (for single mode 1310nm)
•  Mellanox MFM1T02A-SR 850nm 10G

Video Input IP

• SMPTE ST 2110, 2022-6

• YCbCr 4:2:2 10-bit
• Single channel* input available when using ST 2110 or ST 2022-6 to receive

2K/HD

•  4-channels input available when using ST 2110-23 to receive 4K/UltraHD**
•  ANC support
•  Rx support for Narrow Senders**

*Capture and simultaneous monitoring is supported up to 2K/HD
**SMPTE ST 2110 only

«
...
69
70
71
72
73
...
»

Содержание Io IP























































































Отзывы:

Нет отзывов

Похожие инструкции для Io IP

Бренд: JBL Страницы: 24

Hardon mini R1271C

Бренд: Caen RFID Страницы: 39

Бренд: J&M Страницы: 8

Loft Universal 3399

Бренд: Fermax Страницы: 2

Бренд: Vansco Страницы: 11

Бренд: Ergoswiss Страницы: 27

Бренд: NAIM Страницы: 31

Бренд: Hama Страницы: 76

Бренд: Blue Giant Страницы: 24

Бренд: JK Audio Страницы: 24

Бренд: Jet Страницы: 16

Бренд: b-red Страницы: 8

Бренд: M-system Страницы: 3

AMETEK ORBIT ACS Series

Бренд: Solartron Metrology Страницы: 63

Бренд: GAI-Tronics Страницы: 17

Бренд: Crestron Страницы: 26

Бренд: Axis Страницы: 211

ERCOLE QK-E2500

Бренд: Quilo Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды