Airxcel AHE-125-DN1, Руководство по установке

Страница: 21 / 35

Configuring the Zones Mounting the Aqua-Hot LCD
©Aqua-Hot®
125DN Installation Manual REV 220419
©Aqua-Hot®
125DN Installation Manual REV 220419
p. 39 p. 38
Operating the LCD
System Status (4):
This item will indicate the current operational status
of the Aqua-Hot. If any faults have triggered, those will be
displayed here.
During normal operation, this should display either
INTERIOR HEAT or HOT WATER relating to the priority and
position of the 3-way valve.
While in INTERIOR HEAT mode, the 3-way valve is
oriented so as to circulate heated antifreeze and water
solution through the heating zones of the RV.
While in HOT WATER mode, the 3-way valve is oriented
so that the heated antifreeze and water solution is
circulated immediately back into the boiler tank. This is
known as “stirring” the tank, and it is done to provide as
much heat as possible to the domestic water line while
water is flowing.
Module Options (5):
Tapping on the module options screen (the 3 lines on the
bottom right of the home screen) will display the screen shown
to the left. This is known as the Module Options screen. From
here, it is possible to access unit diagnostics, activate Quiet
Mode, change the temperature units, adjust screen brightness,
and unit timeout.
Screen Timeout (A):
The screen timeout item sets the amount of time
required to allow the screen to shut-off when idle.
Screen Brightness (B):
This setting changes the screen brightness.
Unit of Measurement (C):
This setting will change the display units of the Aqua-
Hot. Either Fahrenheit or Celsius can be selected.
Aqua-Hot Diagnostics (D):
Tapping on this element will direct you to the Aqua-Hot’s
built-in diagnostic, testing, and troubleshooting tools.
Quiet Mode (E):
This option toggles the Aqua-Hot’s quiet mode. Quiet
mode is a setting where the speed and output of the
heat exchanger fans is reduced to 80%. This is done to
reduce noise of the heat exchangers.
Please note that this feature must be activated and
deactivated as needed.
Configuring the Zones
Introduction:
Once the heat exchangers and thermostats have been wired
to the Aqua-Hot, the Controller must be configured in order to
correctly manage these zones.
Configuration:
In order to configure these zones for first use, locate the
Aqua-Hot LCD screen and navigate to the Aqua-Hot Diagnostics
section.
After holding the serial number section above, you will be
presented with an options panel like the one shown below.
Tap OPTIONS, and then CLIMATE ZONES to access the climate
zone configuration sub-menu.
Changing Zone Settings:
Once the Climate Zone section has been accessed, the
information below will explain how to correctly configure the
zones.
Tap and hold 3
seconds anywhere
in this section
Number of Zones (A):
The Aqua-Hot can control between 1 and 3
heating zones within the RV. Modifying this
will set the Controller to manage 1, 2, or 3
heating zones.
Zone Settings (B):
Zone settings will change the way each zone
is labeled on the home screen of the LCD, as
well as the type of thermostat used in the RV
interior.
Modifying “Temp Input” will change the type of
signal that is expected by the Controller.
• Set to “Thermistor” if an interior thermistor
is to be used.
• Set to “Thermostat” if a traditional ON/
OFF thermostat is to be used.
Modifying “Label” will change how the zone
is displayed. There are three choices; Front,
Mid, and Rear which correspond to the zones
within the RV. See example below.
A
B
RV-Side
Connections &
Components
Inputs from RV
Outputs to RV
Aqua-Hot
Connections &
Components
Inputs from Aqua-Hot
Outputs to Aqua-Hot
Aqua-Hot 5in
LCD Screen
Aqua-Hot
Controller
Figure 85
A
B
C
E
D