AirStage ASHE07GACH, Руководство по установке, Страница: 9 / 144

En-8
6. FIELD SETTING
There are 3 methods for address setting by FIELD SETTING as follows.
Set by either of the methods.
Each setting method is described (1) to (3) below.
(1) IU AD, REF AD SW settings .............. This section (6.1. Setting the address)
(2) Remote controller settings ................. Refer to the wired or wireless remote controller
manual for detailed setting information. (Set IU
AD, REF AD SW to 0)
(3) Automatic address settings................ Refer to the outdoor unit manual for detailed
setting information. (Set IU AD, REF AD SW to 0)
6.1. Setting the address
Manual address setting method
CAUTION
When setting the DIP switch, use an insulated screw driver.
When handling the PCB, static electricity charged in the body may cause malfunction
of the PCB. Follow the cautions below:
• Touch metal part of the indoor and outdoor units for more than 10 seconds to
discharge static electricity charged in the body.
• Do not touch terminals of parts and patterns implemented on the PCB.
(1) Remove the cable clamp.
Screw
Cable clamp
(2) Remove screws of the heat exchanger, and then remove earthing (grounding) wire.
(3) Remove the shield and the connector cover.
(4) Remove 3 thermistors and 3 connectors.
Screw
Screw
Thermistors
Connectors
Connector cover
Shield
Earthing
(grounding)
wire
(5) Remove screws, then remove the control unit.
Control unit
Screw
(6) Set the switches on the PCB.
1
Indoor unit address
Rotary switch (IU AD × 1)...Factory setting “0”
Rotary switch (IU AD × 10)...Factory setting “0”
When connecting multiple indoor units to 1 refrigerant system, set the address at
IU AD SW as shown in the Table A.
2
Refrigerant circuit address
Rotary switch (REF AD × 1)...Factory setting “0”
Rotary switch (REF AD × 10)...Factory setting “0”
In the case of multiple refrigerant systems, set REF AD SW as shown in the Table
A for each refrigerant system.
Set to the same refrigerant circuit address as the outdoor unit.
Rotary switch
(Example: “0”)
Controller PCB
IU AD ×10
IU AD ×1
REF AD ×10
REF AD ×1
RC AD ×1
Rotary switch
(Example: “0”)
Table A
Setting Setting range Type of switch
Indoor unit
address
0 to 63
Setting example
2
IU AD × 10 IU AD × 1
Refrigerant
circuit address
0 to 99
Setting example
63
REF AD × 10 REF AD × 1
• If working in an environment where the wireless remote controller can be used, the
addresses can also be set using the remote controller.
• If setting the addresses using the wireless remote controller, set the indoor unit
address and refrigerant circuit address to “00”.
Address
Rotary
Switch Setting
Address
Rotary
Switch Setting
Refrigerant
circuit
REF AD SW
Indoor unit
IU AD SW
× 10 × 1 × 10 × 1
0
0 0 0 0 0
1 0 1 1 0 1
2 0 2 2 0 2
3 0 3 3 0 3
4 0 4 4 0 4
5 0 5 5 0 5
6 0 6 6 0 6
7 0 7 7 0 7
8 0 8 8 0 8
9 0 9 9 0 9
10 1 0 10 0 0
11 1 1 11 1 1
12 1 2 12 1 2
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
99 9 9 63 6 3
Do not set the indoor unit address (IU AD SW) at 64 to 99.
It may result in failure.
3
Remote controller address
i) 3-wire type
Rotary switch (RC AD SW)...Factory setting “0”
When connecting multiple indoor units to 1 standard wired remote controller, set the
address at RC AD SW in sequence from 0.
Setting Setting range Type of switch
Remote controller
address
0 to 15
Setting
example
0
RC AD
9377773098-01_IM.indb 8 9377773098-01_IM.indb 8 7/12/2012 3:05:24 PM 7/12/2012 3:05:24 PM