manualshive.com logo in svg

Airspan MicroMAX, Руководство по установке оборудования и инструкция пользователя

Поделиться
Скачать
Airspan MicroMAX Скачать руководство пользователя страница 74

                                

MicroMAX Hardware Installation User Guide

 

 

 

 
Page 74 

Commercial in Confidence 

UWB-D00068 Rev J 

 

 

This cable connects between the rear panel of the AC/DC Converter and the -48V Power Input on 
the Front Panel of the BSDU. 

 

Note:

 Ensure that:  

The 

POSITIVE

 output of the AC/DC Converter is connected to the 

POSITIVE

 

(Red) input (lower) on the BSDU. 
The 

NEGATIVE

 output of the AC/DC Converter is connected to the 

NEGATIVE

 (Black) input (upper) on the BSDU. 

16.4 Cable Connection 

 

Caution:

 Confirm that all inputs to the AC/DC converter are either 

disconnected or powered off prior to installing the cable, otherwise damage 
may occur to either or both devices. 

 

To connect the BSDU to AC/DC Converter Cable 

1.  Connect the end of cable 63000110 labeled 

BSDU

 to the 

PS MNG

 port on the back panel of 

the BSDU, as shown below. 

 

Figure 63 - BSDU to PS MNG port 

2.  Connect the end of cable 63000110 marked ‘PSU’ to the ‘J1’ port on the back panel of the 

AC/DC Convertor, as shown below. 

 

Figure 64 - PSU to J1 port 

3.  Connect the Black crimped wire from the 25-pin cable connected to Port J1 on the back 

panel of the AC/DC Convertor to the –VDC (Negative) output of the AC/DC Convertor on the 
back panel, as shown below. 

Содержание MicroMAX





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды