manualshive.com logo in svg

Airspan MicroMAX, Руководство по установке оборудования и инструкция пользователя

Поделиться
Скачать
Airspan MicroMAX Скачать руководство пользователя страница 19

                                

MicroMAX Hardware Installation User Guide

 

 

 

 
Page 19 

Commercial in Confidence 

UWB-D00068 Rev J 

 

 

 

Figure 2 - Typical Setup 

2.5  Power 

¾

  The SDA-4S is a switch providing the MicroMAX BSR with -48 VDC power supply, and 

10/100BaseT interface with the subscriber's PCs/network. 

¾

  The BSDU is also responsible for providing BSRs with -48 VDC power supply and for 

synchronizing BSDUs, BSRs and Base Stations (when a GPS is implemented). 

¾

  An external AC/DC power converter (optional) is available in the event -48 VDC is not 

available at BS site. Contact your Airspan supplier. 

2.6  Models 

The MicroMAX is available in the following basic physical designs:  

¾

  MicroMAX with a built-in (integral), internal antenna. 

¾

  MicroMAX with an N-type type RF connector for connecting an optional third-party 

external antenna. 

 

Note:

 A MicroMAX with an N-type port for attaching a third-party external 

antenna does not provide a built-in antenna. 

 

Содержание MicroMAX





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды