manualshive.com logo in svg

Airspan MicroMAX, Руководство по установке оборудования и инструкция пользователя

Поделиться
Скачать
Airspan MicroMAX Скачать руководство пользователя страница 12

                                

MicroMAX Hardware Installation User Guide

 

 

 

 
Page 12 

Commercial in Confidence 

UWB-D00068 Rev J 

 

 

FCC Notice 

Federal Communication Commission Notice 

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used 
in accordance with the instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his/her own 
expense. 

Fixed and base stations transmitting a signal with an emission bandwidth greater than 1 MHz 
must not exceed an ERP of 1000 watts/MHz and an antenna height of 305 m HAAT, except that 
antenna heights greater than 305 m HAAT are permitted if power levels are reduced below 1000 
watts/MHz ERP. 

GPS Compliance  

The GPS is in compliance with the essential requirements and other relevant provisions of 
Directive 1999/5/EC." 

The GPS complies with the following EMC Common Regulatory Testing standards: 

¾

  EN55022: Radiated and Conducted Emissions 

¾

  CISPR 22: Class B 

¾

  EN 50081-1: Generic Emissions Class B 

¾

  EN 50082-1: Generic Immunity Class B 

¾

  EN 61000-4-2: Electrostatic Discharge Immunity 

¾

  EN 61000-4-3: Radiated RF EM Field Immunity Test 

¾

  EN 61000-4-4: Electrical Fast Transient/Burst Test 

¾

  EN 61000-4-6: Conducted Immunity 

¾

  EN 61000-4-8: Magnetic Field Immunity 

 

Note:

 A GPS is required for synchronizing between TDD/FDD sectors. 

 

Содержание MicroMAX





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды