manualshive.com logo in svg

Airspan MicroMAX, Руководство по установке оборудования и инструкция пользователя

Поделиться
Скачать
Airspan MicroMAX Скачать руководство пользователя страница 43

                                

MicroMAX Hardware Installation User Guide

 

 

 

 
Page 43 

Commercial in Confidence 

UWB-D00068 Rev J 

 

 

8  AC/DC Power Converter 

This section provides a description of the external

 AC/DC Power converter

 - Optional. 

The third-party external AC/DC Power Converter is an optional unit that connects to the BSDU in 
the event there is no -48VDC availability at the Base Station site 

(110/220 input)

. The AC/DC 

Power Converter chassis fitted with one PS Unit for BSDU (PC-BSDU-1) supports up to 8 BSRs. 
An additional PS unit is available (optional) for redundancy. 

The figure below illustrates the AC/DC Power Converter's physical dimensions. 

 

Figure 23 - AC/DC Power Converter 

8.1.1 Physical 

Dimensions 

The AC/DC power converter physical dimensions are described in the following table. 

Table 21 - AC/DC power converter dimensions 

Parameter Value 

Comment 

Height 

43.2 mm (1.7 inches) 

Width 

482.6 mm (19 inches) 

Depth 

228.6 mm (9 inches) 

 

The physical dimensions exclude the bracket flanges for mounting.

8.2  Redundant PS Unit 

The RPSU-BSDU-1 is a redundant PS Unit for the BSDU AC/DC power converter. The power 
factor corrected (PFC) front ends provide a 48 VDC output for distributed power applications. The 
small 1U by 2U size allows for configurations of either height in hot-swap redundant systems 
while its internal fan and cooling design permits wide use with reliable operation. 

The figure below illustrates the redundant PS Unit. 

Figure 24 - RPSU-BSDU-1 

 

Содержание MicroMAX





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды