Airspan MicroMAX Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 100

Airspan MicroMAX Скачать руководство пользователя страница 10

MicroMAX Hardware Installation User Guide

Page 10

Commercial in Confidence

UWB-D00068 Rev J

Warnings and Cautions

Human Exposure to Radio Frequencies

The MicroMAX should be installed and operated from a minimum distance of 2 meters to your
body.

Radio Interference

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment on and off, the technician is encouraged to try
to correct the interference by performing one or more of the following measures:

¾

Re-orientate or relocate the receiving antenna

¾

Increase separation between the equipment and receiver

¾

Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected

Avoiding Radio Interference

¾

This transmitter must not be co-located or operating in conjunction with any antenna or

transmitter.

¾

Ensure a minimum of 1-meter separation between co-located BSRs.

Modifications

Any changes and modifications to this device that are not expressly approved by Airspan
Networks may void the user's authority to operate the equipment.

General

¾

Only qualified personnel should be allowed to install, replace, and service the equipment.

¾

The device cannot be sold retail, to the general public or by mail order. It must be sold to

dealers.

¾

Installation must be controlled.

¾

Installation must be performed by licensed professionals.

¾

Installation requires special training.

¾

The MicroMAX radio and antenna should be installed ONLY by experienced installation

professionals who are familiar with local building and safety codes and, wherever
applicable, are licensed by the appropriate government regulatory authorities. Failure to
do so may void Airspan's WiMAX product warranty and may expose the end user or the
service provider to legal and financial liabilities. Airspan and its resellers or distributors
are not liable for injury, damage or violation of regulations associated with the installation
of outdoor units or antennas.

«
...
8
9
10
11
12
...
»

Содержание MicroMAX





































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды