manualshive.com logo in svg

Airspan AirSynergy3, Руководство по установке

Поделиться
Скачать
Airspan AirSynergy3 Скачать руководство пользователя страница 9

                                 

AirSynergy3 Equipment Installation Guide

 

Page 9 |                                     Commercial in Confidence                                           SYN-UG-018 

 

1  About this Guide 

This section discusses the purpose, intended audience, conventions, referenced documentation and 
organisation for this guide. 

1.1  Purpose 

This guide provides the workflow and step-by-step procedures for Installation of the AirSynergy 
equipment.  These procedures include: 

Verify Prerequisites 
Install the AirSynergy3 Radio equipment 
Install the PSU equipment 
Connect and manage cables 
Commission and discover via Netspan, to be ready for full configuration 
 

1.2  Intended Audience 

This guide is intended for persons who are responsible for installing  AirSynergy equipment.  These 
persons should have a working knowledge of the equipment. 

1.3  Conventions 

This document uses the following informational conventions. 

Icon 

Description  

 

 

Checkpoint:  

Marks a point in the workflow where there may be an exit or branch 

to some other procedure.  At each 

Checkpoint 

the reason for an exit or branch is 

given along with specific directions to locate the entry point in the other 
procedure. 

 

 
Reference:  

Gives a resource in the workflow that may be needed to complete a 

procedure along with specific directions to use the resource. 

 

 
Caution:  

Describes a possible risk and how to lessen or avoid the risk. 

 

 
Advice:  

Provides a recommendation based on best practice. 

 

 

 
Note:  

Provides useful information. 

 

Содержание AirSynergy3


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды