AirMan SDG40S-8B1 Скачать руководство пользователя | Manualshive

Страница: 3 / 69

background image

Preface

A040491

Thank you for having selected our “AIRMAN” product.

◆

This manual explains about the proper operation and daily inspection and maintenance of this
machine.

◆

In order to use a machine safely, people with sufficient knowledge and sufficient technology need to
deal with it.

◆

Before operating the unit, read the manual carefully, fully understand its operation and
maintenance requirement. Maintain

“SAFETY OPERATION AND PROPER MAINTENANCE OF

THE UNIT”

.

Be sure to follow safety warnings and cautions given in the manual.
Unsafe operation could cause serious injury or death.

◆

For details of handling, maintenance and safety of the engine, see the Engine Operation Manual.

◆

Keep the manual available at all times for the operator or safety supervisor.

◆

If the manual is lost or damaged, place an order with your dealer for another copy.

◆

Be sure that the manual is included with the unit when it is handed over to another user.

◆

There may be some inconsistency in detail between the manual and the actual machine due to
improvements of the machine. Ask your dealer if you have any questions or problems.

◆

If you have any questions about the unit, please inform us the model and serial number. A plate
stamped with the model and serial number is attached to side of the unit.

◆

Each illustrated figure (Fig.) has a number
(for instance, A040491) at the right bottom.
This number is not a part number, but it is
used only for our reference number.

Discount-Equipment.com

«
1
2
3
4
5
...
»

Содержание SDG40S-8B1






































































Отзывы:

Нет отзывов

Похожие инструкции для SDG40S-8B1

Бренд: 3onedata Страницы: 3

Бренд: Magnum Energy Страницы: 2

Бренд: Magnum Energy Страницы: 62

Бренд: HQ Страницы: 76

Бренд: R&S Страницы: 40

Бренд: Harmonic Страницы: 27

Бренд: ICP DAS USA Страницы: 4

blueplanet 15.0 TL3

Бренд: Kaco Страницы: 188

Бренд: Kaiser Baas Страницы: 3

Бренд: M-Audio Страницы: 3

Бренд: Yamaha Страницы: 2

Бренд: Korenix Страницы: 2

Бренд: PRO SIGNAL Страницы: 2

EdgeVis HD-IP200

Бренд: Digital Barriers Страницы: 34

Бренд: IONODES Страницы: 23

Бренд: OneFex Страницы: 37

Бренд: Avonic Страницы: 6

Бренд: Optical Systems Design Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды