AirMan SDG40S-8B1 Скачать руководство пользователя

Страница: 50 / 69

5. Periodic Inspection/Maintenance

5.5.14

Clean inside of the oil fence and check it for any rust

[Every 1 years]

①

Remove the oil filler cap cover, fuel pipes and electric wire connected to the fuel tank.

②

Remove 6 pieces of the bolts connecting oil fence and the machine with the lifting eye hooked with

the crane.

③

Lift up the machine to separate the oil fence from the machine.

④

Check and clean the inside of the oil fence.



Check the inside of the oil fence for dust, fur and other foreign matter and check it for any rust.



When the oil fence is found rusted, remove the rust outside and inside and paint it again.



Should any leakage be found, contact your dealer or us directly.

⑤

Check whether the seal rubber attached on the top of oil fence is slanted or curved.

⑥

Combining this machine and the oil fence, tighten the nuts 6 pieces.

⑦

Install oil filler cap cover, fuel pipes and also electric wires.

Combining this machine

and oil fence with the

nuts 6 pieces

Oil fence

Fuel Tank

Oil filler cap cover

[This machine]

Seal rubber

Connecting to the

electric wire

Connecting to the
fuel pipes

A100422

Discount-Equipment.com

Содержание SDG40S-8B1






































































Результаты поиска

Содержание SDG40S-8B1

Отзывы:

Похожие инструкции для SDG40S-8B1

Бренды по названию

Популярные бренды

AirMan SDG40S-8B1, Инструкция по эксплуатации

Результаты поиска

Содержание SDG40S-8B1

Отзывы:

Похожие инструкции для SDG40S-8B1

Бренды по названию

Популярные бренды