AirMan SDG40S-8B1 Скачать руководство пользователя

Страница: 39 / 69

4. Operation

4.7 Stopping Procedures

①

Switch “OFF” the breaker on the operation panel of the generator.

②

After performing cooling down operation about 5 minutes, place the starter switch to the“STOP”

position to stop the engine.

③

While the machine is kept unused, keep the operation selector switch placed to the “OFF”position.

4.8 Emergency Stop



The Emergency Stop button should be used only for emergency stop.



Regularly check the operating performance.



If it is necessary to stop the generator for emergency,
press the Emergency Stop button



To reset the button, turn the button head in the
direction of the arrow. If it is not reset, the machine
cannot restart to operate

4.9 Air Bleeding

Should the machine stop due to the shortage of fuel, perform the air bleeding operation according to
the following procedures.

①

Place the operation selector switch to the “MANUAL” position.

②

Place the starter switch to “RUN” position to put electromagnetic pump into operating conditions.

③

Air bleeding will be completed within 20-30 seconds.

④

Place the operation mode selection switch to “LOW” position and start engine.

⑤

Keep warming up operation for 3 minutes after engine has started.

⑥

Then place the operation mode selection switch to “HIGH” position and raise engine speed up to the
rated speed (RPM). Thereafter, repeat mode selection operation “LOW”

⇔

“HIGH”several times.

H980178

H980179

Discount-Equipment.com

Содержание SDG40S-8B1






































































Результаты поиска

Содержание SDG40S-8B1

Отзывы:

Похожие инструкции для SDG40S-8B1

Бренды по названию

Популярные бренды

AirMan SDG40S-8B1, Инструкция по эксплуатации

Результаты поиска

Содержание SDG40S-8B1

Отзывы:

Похожие инструкции для SDG40S-8B1

Бренды по названию

Популярные бренды