AirMan SDG40S-8B1 Скачать руководство пользователя

Страница: 45 / 69

5. Periodic Inspection/Maintenance

5.5.2 Change engine oil filter

[At 50 hours for the first change and every 500 hours thereafter]

①

When installing a new oil filter

“

”

, spread oil over

the packing

“

”

, and then screw it in. When the

packing touches the sealing surface, further
tighten the filter by approximately two-thirds turn
with a filter wrench.

②

After the oil filter

“

”

is assembled, check if there

are any oil leaks during operation.

(For part number, see 5.3)

5.5.3 Check GFCI receptacles

[Monthly or 250 hours operation, whichever comes first.]



If the generator is stored outdoors, unprotected from the weather, test the GFCI receptacle before
each use.



In case the GFCI has tripped due to the hazard of ground fault currents, investigate the cause and
correct it.

Regularly check the GFCI operation for safety.

①

Unplug all appliances from the generator.

②

Start the engine.

③

Turn each single-phase and three-phase breaker ON.

④

Press the TEST BUTTON



The RESET BUTTON should extend with a click.



If the RESET BUTTON does not extend, contact your

nearest dealer.

⑤

Press the RESET BUTTON

⑥

When the RESET BUTTON extends during peration.



Unplug all appliances from the GFCI protected
receptacle.



Press the RESET BUTTON:

IF THE GFCI CANNOT BE RESET: The GFCI is faulty. Contact your nearest dealer.

IF THE GFCI RESETS PROPERLY: Check the appliance or the power cord.

Reset button

Test button

A040270

H000049

Discount-Equipment.com

Содержание SDG40S-8B1






































































Результаты поиска

Содержание SDG40S-8B1

Отзывы:

Похожие инструкции для SDG40S-8B1

Бренды по названию

Популярные бренды

AirMan SDG40S-8B1, Инструкция по эксплуатации

Результаты поиска

Содержание SDG40S-8B1

Отзывы:

Похожие инструкции для SDG40S-8B1

Бренды по названию

Популярные бренды