Air-Pol Feniks STUDENT Скачать руководство пользователя страница 22

Страница: 22 / 38

Feniks STUDENT Instruction Manual, No.

033-02-100

edition

, 2012, page

AIR-POL Sp. z o.o.

– 05-120 Legionowo, ul. Olszankowa 52, www.air-pol.com.pl

tel.: (+4822) 774 0711, (+4822) 784 1595, (+4822) 774 4832, fax (+4822) 784 9640, @: [email protected]

CONNECTING MAIN PARACHUTE RISERS TO THE HARNESS/CONTAINER. THE THREE-RING
SYSTEM.

3.1.

THREE-RING RELEASE SYSTEM ASSEMBLY

The release system serves the purpose of cutting away the main canopy in case it does not inflate properly (in case it

malfunctions). Each Feniks harness/container system is fitted with an “Anti-Twist” system preventing a difficult or impossible

pull-out of the cutaway handle in a suspension line twist situation.

The release system consists of the following components, all of which have to be checked prior to assembly (whether they

are operational and clean):

Fot. 46

•

Harness ring – largest (1)

•

Terminal riser ring – medium (2)

•

Closing loop ring – smallest (3)

•

Closing loop (4)

•

Riser ring (5)

•

Protective casing of the yellow blocking cable

(6)

•

Protective casing eye (7)

•

Yellow blocking cable (8)

•

Main parachute riser (9)

•

RSL system tape connector ring (10)

•

RSL system tape carabineer (11)

•

Cutaway handle (12)

•

Protective casing of the loose end of the yellow

blocking cable (13)

Fot. 47

Place yellow cables (8) in protective casings,

the ends of which are placed between chest

strap layers.

Place the cutaway handle (12) in the pouch

between the right-hand side vertical main

straps of the harness. The handle shall be

attached to the straps firmly and deeply with

the use of Velcro tape.

Fot. 48

Prepare the parachute canopy for connection

to the harness. The canopy’s suspension lines

should be free of entanglement. This is best

done when the container and canopy are

arranged as if for packing: the canopy should

be placed with cell openings (vents) facing

downwards, the harness/container’s flaps

should be facing upwards.

Untwisted risers should be placed in front of

the container – riser rings should be lower,

steering toggles should be higher.

Содержание Feniks STUDENT







































Результаты поиска

Содержание Feniks STUDENT

Отзывы:

Похожие инструкции для Feniks STUDENT

Бренды по названию

Популярные бренды

Air-Pol Feniks STUDENT, Инструкция по эксплуатации

Результаты поиска

Содержание Feniks STUDENT

Отзывы:

Похожие инструкции для Feniks STUDENT

Бренды по названию

Популярные бренды