AGL GradeLight 3000 страница 35 Скачать руководство пользователя | Manualshive

Страница: 35 / 40

background image

34

SET

After a change, check the laser LCD and wait until SET
appears again on the screen, and move the beam again if
needed.

To save the calibration (beam position), press the

Lock

button on the Remote (or the

ENT

button on the laser

keypad).

If it is not desired to save changes, turn the laser off.

To leave the CALIBRATION mode, move the cursor to

EXIT

and press

ENT

.

(If using the Remote, move up the menu using the Center
Line button and move down the menu using the Standby
(ZZZ) button. Press the Lock button instead of ENT.)

To leave the SET UP mode, move the cursor to

EXIT

and

press

ENT

(or LOCK on the Remote).

Final Calibration Check

Re-check the new calibration using the steps shown in the previous section with Stakes A
and B. If the marks are no more than 1/8 inch apart at 100 feet (at 30 m, no more that 3 mm
apart), the laser is within the accuracy spec and calibrated correctly.

«
...
33
34
35
36
37
...
»

Содержание GradeLight 3000









































Отзывы:

Нет отзывов

Похожие инструкции для GradeLight 3000

Бренд: WAGER Страницы: 22

Бренд: Vaisala Страницы: 2

Бренд: CAS Corporation Страницы: 20

Duomat Evolution DeLuxe

Бренд: Dennerle Страницы: 27

Бренд: Seaward Страницы: 2

Бренд: B meters Страницы: 3

Бренд: Hanna Instruments Страницы: 28

Бренд: Kawai Страницы: 28

Бренд: THORLABS Страницы: 63

Бренд: THORLABS Страницы: 20

Бренд: EIJKELKAMP Страницы: 11

Бренд: Kimo Страницы: 80

Бренд: LI-COR Страницы: 92

Бренд: Samick Страницы: 48

Бренд: H&B Страницы: 45

Бренд: Datcon Страницы: 100

Бренд: Pro'sKit Страницы: 48

Бренд: Velleman Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды