manualshive.com logo in svg

AGL GradeLight 3000, Руководство пользователя

Поделиться
Скачать
AGL GradeLight 3000 Скачать руководство пользователя страница 31

30

TROUBLESHOOTING

Indication on LCD

Laser Beam

Reason

Remedy

Flashes evenly
----- ----- -----

Laser is 

leveling

Wait until self-leveling is 
complete.

Pulses in

2 short flashes

-- --

-- --

-- --

Self-leveling

range is 

exceeded

Change position of laser in 
direction arrows indicate.  When it 
is within range, the warning will 
disappear and self-leveling will 
begin.

Pulses in

2 short flashes

-- --

-- --

-- --

Cross axis 

not level

Rotate laser slightly to the left or 
right until the bubble is between 
the lines on the electronic vial.

CHECK CAL

Reminder 

that laser has 

reached 2000 

hrs of use, or 

the interval 

set by the 

user.

The laser can continue to be 
used.  The calibration should be 
checked on a regular basis.  This 
is a reminder of operating time 
intervals.  To delete this 
message, see “Set Up Mode 
Menu Options.”

ERROR 0

No beam; error 

turns unit off 

automatically

Data error

Turn unit on again.  Check 
calibration.  If the message
appears again, contact an 
authorized service center.

On

Low Battery

Change power source.

Laser does not power-up

·

Check battery.

·

Hold the ON button for at least 3 seconds (if unit has not been powered up for a while)

Loss of distance

·

Check window on laser where beam is emitted and clean with a soft cloth if needed.

Dancing laser spot

·

Use a blower to reduce refraction and scintillation problems.

Remote control not working

·

At longer distances, ensure the remote is in the “line of sight” of the laser.  Point the 
remote directly at the reception window on GradeLight and remove any obstacles 
between remote and laser.

·

Check and replace batteries.

·

Operating range is reduced due to rain or fog – use at closer range.

·

Operating range is reduced due to dirt on the reception window of the GradeLight –
clean with a soft cloth.

Содержание GradeLight 3000









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды