manualshive.com logo in svg

AGL GradeLight 3000, Руководство пользователя

Поделиться
Скачать
AGL GradeLight 3000 Скачать руководство пользователя страница 12

11

Keypad and LED Overview

LEFT Red LED

Blinking

AutoTarget has received the rotating laser beam 
on the left side of the reception field, and the 
fine auto alignment run is starting

Green ON/OFF LED

Solid

AutoTarget is on, auto alignment is not running 
yet, or has just been successfully finished

Green SEEK LED

Blinking

Auto alignment is running and seeking the 
AutoTarget in a coarse run

Solid

Auto alignment is running and seeking the 
AutoTarget‘s center in a fine mode

RIGHT Red LED

Blinking

AutoTarget found

Both LEFT and RIGHT LED

Blinking

Target has timed out (see 16 for detailed 
description)

Solid

Target is in wide seek mode

LEFT red LED and ON/OFF 
LED

Solid

While in laser seek mode, shows rotating laser 
beam is left off center

RIGHT red LED and ON/OFF 
LED

Solid

While in laser seek mode, shows rotating laser 
beam is right off center

LEFT and RIGHT red LED 
and ON/OFF LED

Solid

While in laser seek mode, shows rotating laser 
beam is in center

1 up to 4 LED's

Solid

lit for a second after ON/OFF button is pushed 
to show the battery voltage:

if battery voltage is more than 5,7V, all LED's lit

if battery voltage is less than 5,2V, the left red, 
the green ON/OFF LED and green auto LED lit

Содержание GradeLight 3000









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды