Agilent Technologies U1251A Скачать руководство пользователя

Страница: 83 / 168

Changing The Default Setting

Agilent U1251A/U1252A User’s and Service Guide

Table 3

Available setting options in Setup mode

Menu item

Available setting options

Default factory

setting

Display

Description

Display

Description

rHoLd

(1)

Refresh Hold

OFF

Enables Data Hold (manual trigger)

500

100–1000

Sets variation count that determines Refresh Hold
(auto trigger)

d-LoG

Data logging

Hand

Enables manual data logging

Hand

1–9999 s

(2)

Sets interval for automatic data logging

t.CoUP

Thermocouple

tYPE

Sets thermocouple type to K-type

tYPE

(3)

Sets thermocouple type to J-type

rEF

Reference impedance

for dBm measurement

1–9999

(2)

Sets reference impedance for dBm measurement

FrEq

Minimum frequency

that can be measured

0.5 Hz, 1 Hz, 2

Hz, 5 Hz

Sets minimum frequency that can be measured

0.5 Hz

APF

Auto power off

1–99 m

Sets timer for auto power off

10 m

OFF

Disables auto power off

PErnt

Percentage scale

0–20 mA, 4–20

Sets % scale readout

4–20 mA

bEEP

Frequency of beep

sound of meter

2400 Hz, 1200

Hz, 600 Hz,

300 Hz

Sets frequency of beep sound of meter

2400 Hz

OFF

Disables beep sound of meter

b-Lit

Backlit display

1–99 s

Sets timer for auto turn-off for backlit display

30 s

OFF

Disables auto turn-off for backlit display

bAUd

Baud rate

2400 Hz, 4800

Hz, 9600 Hz,

19200 Hz

Sets baud rate for remote communication (remote
control with PC)

9600 Hz

PArtY

Parity check

En, Odd, nOnE Sets even, odd or no parity check for remote com-

munication (remote control with PC)

nOnE

dAtAb

Data bits

7-bit, 8-bit

Sets data bit length for remote communication
(remote control with PC)

8-bit

ECHO

Echo

ON, OFF

Enables return of characters to PC when set to
ON

OFF

Содержание U1251A









































































































































































Результаты поиска

Содержание U1251A

Отзывы:

Похожие инструкции для U1251A

Бренды по названию

Популярные бренды

Agilent Technologies U1251A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1251A

Отзывы:

Похожие инструкции для U1251A

Бренды по названию

Популярные бренды