manualshive.com logo in svg

Agilent Technologies G1369C, Руководство пользователя, Страница: 61 / 66

Поделиться
Скачать
Agilent Technologies G1369C Скачать руководство пользователя страница 61

G1369C LAN Interface User Manual

61

Getting Help

3

Glossary

LED

Light Emitting Diode

MAC address

Media Access Control address, a hardware address that 
uniquely identifies each node of a network.

MIO

Modular Input/Output; interface specification from 
Hewlett-Packard

RJ-45 connector

Registered Jack-45, an eight-wire connector used commonly to 
connect computers onto a local-area networks (LAN), especially 
Ethernets. RJ-45 connectors look similar to the RJ-11 
connectors used for connecting telephone equipment, but they 
are somewhat wider.

Subnet Mask

 A mask used to determine what subnet an IP address belongs 
to. Subnetting enables the network administrator to further 
divide the host part of the address into two or more subnets.

TCP/IP

Transmission Control Protocol/Internet Protocol; LAN 
(Ethernet) protocol

Telnet

A terminal emulation program for TCP/IP networks such as the 
Internet.

Table 13

Glossary

Term / Acronym

Definition

Содержание G1369C



































































Отзывы:

Нет отзывов