Agilent Technologies G1369C Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 66

Agilent Technologies G1369C Скачать руководство пользователя страница 31

G1369C LAN Interface User Manual

31

Getting Started

2

Automatic Configuration with Bootp

5

Press OK. The parameter are added to the Bootp Manager, see

Figure 18

and added to the TabFile, see

Figure 16

on page 29:

Figure 19

Bootp Manager - check your entries

6

Press Exit Manager and OK to exit the Agilent Bootp Service.

7

Now turn on the module with the detector, wait about 30- 60 seconds
and view the LogFile, see

Figure

. It should display the request from

the detector with the hardware (MAC) address.

LogFile - the detector has received the parameter

02/03/05 16:33:56 PM
Status: BOOTP Request received at outer most layer
Status: BOOTP Request received from hardware address: 0030D30A0838
Status: found 134.40.27.95 WADI1171:
Status: Host IP Address is: 134.40.29.56
Status: Reply to BOOTP Request has been sent
Status: BOOTP Request finished processing at outer most layer

«
...
29
30
31
32
33
...
»

Содержание G1369C



































































Отзывы:

Нет отзывов