Agilent Technologies G1369C Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 66

Agilent Technologies G1369C Скачать руководство пользователя страница 18

18

G1369C LAN Interface User Manual

2

Getting Started

Installing and Cabling the LAN Interface Card

2

Note the MAC (Media Access Control) address for further reference. The
MAC or hardware address of the LAN Interface Card is a world wide
unique identifier. No other network device will have the same hardware
address. The MAC address can be found on a label on the card (see

Figure 6

on page 17).

Figure 7

MAC-Label

3

Turn off instrument line power or remove the power cord before
installing the LAN Interface Card.

4

On your instrument, identify the option slot for the MIO accessory card.

5

Remove any blank cover plates and ensure that the slot is empty.

Figure 8

Location of LAN Interface Card (e.g. 1100/1200 series detector)

Part number of the LAN Interface Card, see

page 56

Revision Code, Vendor, Year and Week of assembly
MAC address
Country of Origin

G1369-65810
BB ZZ 1103 MSS-A
MAC 0030D3177321
Made in Germany

N O T E

If the module has the 1100 CAN modification board installed, it probably has a revision 1
mainboard and will not accept the LAN interface. Refer to

“LAN Interface Card

Compatibility”

on page 13

«
...
16
17
18
19
20
...
»

Содержание G1369C



































































Отзывы:

Нет отзывов