Agilent Technologies G1369C Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 66

Agilent Technologies G1369C Скачать руководство пользователя страница 27

G1369C LAN Interface User Manual

27

Getting Started

2

LAN Interface Card Configuration

Link Configuration Selection

The LAN Interface Card supports 10 or 100 Mbps operation in full- or
half- duplex modes. In most cases, full- duplex is supported when the
connecting network device - such as a network switch or hub - supports
IEEE 802.3u auto- negotiation specifications.

When connecting to network devices that do not support auto- negotiation,
the LAN Interface Card will configure itself for 10- or 100- Mbps
half- duplex operation.

For example, when connected to a non- negotiating 10- Mbps hub, the LAN
Interface Card will be automatically set to operate at 10- Mbps half- duplex.

If the card is not able to connect to the network through auto- negotiation,
you can manually set the link operating mode using link configuration
switches on the card.

Table 7

Link Configuration Switches

SW 1

SW 2

SW 3

SW 7

SW 8

Link Configuration

OFF

-

-

OFF

OFF

speed and duplex mode determined by
auto-negotiation

ON

OFF

OFF

OFF

OFF

manually set to 10 Mbps, half-duplex

ON

OFF

ON

OFF

OFF

manually set to 10 Mbps, full-duplex

ON

ON

OFF

OFF

OFF

manually set to 100 Mbps, half-duplex

ON

ON

ON

OFF

OFF

manually set to 100 Mbps, full-duplex

1 2 3 4 5 6 7 8

ON

N O T E

Compared to the G1369A LAN Card, SW 7 and SW 8 must be always in OFF position on the
G1369B/B LAN Card, otherwise the selected modes are not working.

«
...
25
26
27
28
29
...
»

Содержание G1369C



































































Отзывы:

Нет отзывов