Agilent Technologies G1369C Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 66

Agilent Technologies G1369C Скачать руководство пользователя страница 55

G1369C LAN Interface User Manual

55

Getting Help

3

Troubleshooting

Error Messages

The error messages are shown in the LAN Interface Card Status Page on
the Control Module (G1323A/B) only, refer to

“With Handheld Controller

G1323B”

on page 44.

Figure 45

LAN Interface Card Status Page (complete)

If status "Error" shows up, possible error conditions are listed below.

Agilent Technologies G1369C
FW Revision : B.06.40 0003
MAC Address : 0030d31b8417
--------------------------------
Init Mode : Bootp
--------------------------------
TCP/IP Properties
- active -
IP Address : 0.0.0.0
Subnet Mask : not specified
Def. Gateway : not specified
- stored -
IP Address : 134.40.24.160
Subnet Mask : 255.255.248.0
Def. Gateway : 134.40.24.1
--------------------------------
TCP/IP Status : Error
Bootp timeout
--------------------------------
Controller : not connected

Possible reasons:

Bootp server not started or no
settings for this MAC address
found

Table 11

Error conditions

Error

Description

Action

Bootp timeout

No reply on Bootp request received

Start Bootp server and/or add settings
for the LAN Interface Card.

Bootp reply incomplete

Bootp reply contained not all
information

Complete the neccessary information

Gateway in unreachable network

Default Gateway does not match the
specified IP address and Subnet Mask

Correct the settings

«
...
53
54
55
56
57
...
»

Содержание G1369C



































































Отзывы:

Нет отзывов