manualshive.com logo in svg

Agilent Technologies E8364-60105, Установочная инструкция, Страница: 8 / 37

Поделиться
Скачать
Agilent Technologies E8364-60105 Скачать руководство пользователя страница 8

8

  

                                                                                                                            

  

Installation Note E8364-90022

Test Equipment Required for Post-Upgrade Adjustments

Step 1. Verify the Model, Serial, and Option Numbers of the Analyzer

Refer to the License Key Certificate supplied with the kit: 

• Verify that the analyzer’s model and serial numbers match those on the certificate.

• Verify that the option number on the certificate matches the option described by this 

installation note.

If the model, serial, or option number do not match the expected results, you will not be able 
to install the option. If this is the case, contact Agilent for assistance. Refer to 

“Contacting 

Agilent” on page 3

.

Description

Agilent Part Number

Power meter

E4418B/E4419B

Power sensor, Type-N (100 kHz–4.2 GHz)

8482A

Power sensor, 2.4 mm (4.2 GHz–50 GHz)

8487A

Power sensor, V-Band (50 GHz–67 GHz)

a

a. This sensor and adapter must be calibrated together by the Agilent factory. The data supplied 

are only valid as long as the sensor and adapter remain connected.

V8486A

Adapter, WR-15 to 1.85 mm (m)

a

V281B

Adapter, 1.85 mm (f) to 1.85 mm (f)

b

b. The 1.85 mm connector has the same ruggedness and is compatible with the 2.4 mm connec-

tor. 1.85 mm and 2.4 mm connectors and adapters may be used interchangeably.

85058-60114

Adapter, 3.5 mm (m) to 2.4 mm (f)

11901D

Adapter, 2.4 mm (f) to 2.4 mm (f)

b

11900B

Adapter, Type-N (f) to 2.4 mm (f)

11903B

Adapter, SMA (m) to SMA (f), right angle

1250-1249

Test cable, 2.4 mm (f) to 2.4 mm (f)

b

 or

Test cable, 1.85 mm (f) to 1.85 mm (f)

b

85133C

N4697E

5/16-inch, open-end torque wrench (set to 10 in-lbs)

8710-1765

1/4-inch, open-end wrench, thin profile

8710-0510

Содержание E8364-60105






































Отзывы:

Нет отзывов