Agilent Technologies E8364-60105 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 37

Agilent Technologies E8364-60105 Скачать руководство пользователя страница 33

Installation Note E8364-90022

33

Remove the Old Overlay

1. From the back side of the front panel, use a blunt object in one of the cutouts in the lower

frame to push the overlay (item

①

) and separate it from the front panel.

2. From the front side of the front panel, pull the overlay completely off and discard it.

3. If any adhesive remains on the front panel surface, it can be removed by rubbing it with

your finger. Do not use a sharp object to remove this adhesive. If necessary, the surface can
be cleaned with isopropol alcohol.

Install the New Overlay

1. Remove the protective backing from the new front panel overlay to expose the adhesive.

2. Starting from either the left or right side,

loosely

place the overlay in the recess on the

lower front panel, ensuring that it fits tightly against the recess edges.

3. Once the overlay is properly aligned, press it firmly onto the surface to secure it.

Figure 24

Front Panel Overlay Replacement

NOTE

The figure above shows the E8364B front panel and floppy disk drive. The
E8364C front panel has a slightly different appearance and does not
include a floppy disk drive.

«
...
31
32
33
34
35
...
»

Содержание E8364-60105






































Отзывы:

Нет отзывов