manualshive.com logo in svg

Agilent Technologies E8364-60105, Установочная инструкция, Страница: 7 / 37

Поделиться
Скачать
Agilent Technologies E8364-60105 Скачать руководство пользователя страница 7

Installation Note E8364-90022                                                                                                                         

 

7

Overview of the Installation Procedure

Step 1. Verify the Model, Serial, and Option Numbers of the Analyzer

Step 2. Remove the Outer and Inner Covers

Step 3. Replace the A12 Source 20

Step 4. Replace the Top Side to Bottom Side Cables

Step 5. Raise the Receiver Deck

Step 6. Remove the Old Bottom Side Hardware and Cables

Step 7. Install the New Hardware and Cables

Step 8. Lower the Receiver Deck

Step 9. Replace the Front Panel Nameplate and Overlay

Step 10. Reinstall the Inner and Outer Covers

Step 11. Enter the New Model Number

Step 12. Perform Post-Upgrade Adjustments

Tools Required for the Installation

ESD Equipment and Supplies Required for the Installation

Description

Agilent Part Number

T-10 TORX driver (set to 9 in-lbs)

N/A

T-20 TORX driver (set to 21 in-lbs)

N/A

5/16-inch torque wrench (set to 10 in-lbs)

N/A

1-inch torque wrench (set to 72 in-lbs)

N/A

Description

Agilent Part Number

ESD grounding wrist strap

9300-1367

5-ft grounding cord for wrist strap

9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire

9300-0797

ESD heel strap (for use with conductive floors)

9300-1308

Содержание E8364-60105






































Отзывы:

Нет отзывов