manualshive.com logo in svg

Agilent Technologies E8364-60105, Установочная инструкция, Страница: 29 / 37

Поделиться
Скачать
Agilent Technologies E8364-60105 Скачать руководство пользователя страница 29

Installation Note E8364-90022                                                                                                                         

 

29

Install the New Cables

CAUTION

Be very careful with these cables with 1.85 mm connectors. They are extremely 
delicate and can be easily damaged.

Using a 5/16-inch torque wrench set to 10 in-lbs, install the following new cables 

in the 

order listed

. These new parts are listed in 

Table 1 on page 4

.

• W2

A21 SOMA 50 to A22 switch

• W3

A22 switch to A23 SOMA 70

• W4

A22 switch to A24 SOMA 70

• W8

A24 SOMA 70 to A29 channel R2 mixer

• W6

A24 SOMA 70 to A26 test port 2 coupler

• W10 A26 test port 2 coupler to A30 channel B mixer

• W7

A23 SOMA 70 to A28 channel R1 mixer

• W5

A23 SOMA 70 to A25 test port 1 coupler

• W9

A25 test port coupler 1 to A27 channel A mixer

• W38 A23 SOMA 70 to A16 test set motherboard J204 (R1)

• W39 A24 SOMA 70 to A16 test set motherboard J205 (R2)

•

①

Wrapped wire cable; A22 switch to A16 test set motherboard J500. Route this cable 
under the cable clamp as shown.

•

②

Ribbon cable; A24 SOMA 70 to A16 test set motherboard J40 (

SOMA70_2

). Shape 

and route this cable as shown.

•

③

Ribbon cable; A23 SOMA 70 to A16 test set motherboard J50 (

SOMA70_1

). Shape 

and route this cable as shown.

Содержание E8364-60105






































Отзывы:

Нет отзывов