manualshive.com logo in svg

Agilent Technologies E8364-60105, Установочная инструкция, Страница: 4 / 37

Поделиться
Скачать
Agilent Technologies E8364-60105 Скачать руководство пользователя страница 4

4

  

                                                                                                                            

  

Installation Note E8364-90022

Items Included in the Upgrade Kit

Check the contents of your kit against the following list. If any item is missing or damaged, 
contact Agilent Technologies. Refer to 

“Contacting Agilent” on page 3

.

Table 1

Option 067 Upgrade Kit (E8364-60105) to Extend the E8364B/C to 67 GHz

Ref.

Desig.

Description

Qty

 Part Number

N/A

Installation note (this document)

1

E8364-90022

N/A

License key certificate

1

5964-5136

N/A

Model number nameplate (for 67 GHz analyzer E8361A)

1

E8361-80001

N/A

Model number nameplate (for 67 GHz analyzer E8361C)

1

E8361-80006

N/A

Front panel overlay, no options

1

E8361-80002

A12

A12 source 20

1

E8361-60002

A17

LOMA 12

1

5087-7247

A18

MA 24

1

5087-7248

A22

Switch

1

5087-7238

A23

SOMA 70, port 1

2

5087-7249

A24

SOMA 70, port 2

A25

Test port 1 coupler

2

5087-7225

A26

Test port 2 coupler

A27

Channel A first converter (mixer)

4

5087-7258

A28

Channel R1 first converter (mixer)

A29

Channel R2 first converter (mixer)

A30

Channel B first converter (mixer)

N/A

Mixer bias board

1

E8361-63044

N/A

SOMA 70 bracket

2

E8361-00002

N/A

Machine screw M3.0 x 10 (for attaching A22 switch)

2

0515-0374

N/A

Machine screw M3.0 x 6 (for attaching SOMA 70 brackets)

6

0515-0430

N/A

Machine screw M3.0 x 25 (for attaching SOMA 70s to brackets)

4

0515-0667

Содержание E8364-60105






































Отзывы:

Нет отзывов