AGCO ROGATOR 418 Скачать руководство пользователя страница 85

Страница: 85 / 86

INDEX

Index 3

RoGator 418

Parking brake warning light

4.2

Pop-up messages and warnings

4.7

Positions of the Traction Control Lever

3.2

Practice Safe Maintenance

1.8

Preparation for Emergencies

1.1

Prevent Vehicle Runaway

1.2

Primary Filter Element

6.7

Priming of the Fuel System

6.9

Proper Lifting Equipment

1.9

Proper Servicing

1.9

Proper Support of Vehicle

1.9

Rear axle in middle position indicator light

4.2

Remote Throttle Control

3.7

Remote Throttle Control

5.9

Removal of Paint before Welding or Heating

1.11

Removing the Wheels

6.11

Replace the Fuel Filter

6.8

Replacing Hydraulic Fluid and Filters in Hydraulic
System

6.13

Replacing the Leakage Oil Filter

6.13

Replacing the Suction and Return Line Filter

6.13

Res 1 / Res 2

3.7

Res 1/ Res 2

5.9

Reset button speedometer

4.2

Restarting a Stalled Engine

5.2

Right turn signal light

4.2

Road Position

3.2

Road Position

3.2

RoGator towing Procedure

2.5

Safe Handling of Fuel - Avoid Fires

1.5

Safe Operation of the Vehicle

1.2

Safe Servicing of Cooling System

1.10

SAFETY

Safety Treads

6.17

Safety Treads and Grips

1.6

Seasonal viscosity Oil and Proper coolant
concentration

7.1

Seat

3.9

Seat depth adjustment

3.9

Seat pan angle adjustment

3.9

Separate Ladder

5.9

Serial Number Identification Plates

2.2

Service Brake (Option)

10.1

Setting display contrast and lighting

4.4

Setting the Track Width

5.6

Sliding the Axle

5.6

Slow Speed Range Switch

3.7

SPECIFIACTIONS

Speed Ranges

10.1

Speed Ranges:

5.3

Speedometer

4.2

Spray pump On / Off

3.7

Spray pump On / Off

5.9

Starting at Low Temperatures

5.2

Starting the Engine

5.2

Stay Clear of Rotating Power Takeoffs and Moving
Parts

1.6

Steering

9.3

Steering

10.1

Stop lamp

3.10

Stopping and Parking the Vehicle

1.4

Storage of Vehicle

6.16

Suction / return line filter and leak oil filter indicator
light

4.2

Sun Visor

3.8

Supplement coolant additives (SCA's)

7.1

Supplemental Coolant Additives (SCA’s)

6.6

Suspension

3.6

Switch for 4-Wheel Steering

5.4

Switching the skid regulator On/Off

5.5

Switching the spray computer On/Off

3.7

Swivel

3.9

System Boom Safety

1.4

Tank and Filter

2.3

Temperature Control Knob

3.10

The alarm display screen

4.7

The graph display

4.6

The main engine display

4.4

The quad and graph parameters

4.6

The quad display

4.5

Towing

2.4

Towing Other Vehicles

1.6

Towing with Engine Disabled

2.4

Towing with Engine Operable

2.4

Track width 1,50 - 2,00 m (Front axle)

5.7

Track width 1,80 - 2,25 m (Front axle)

5.7

Track width 2,00 - 2,25 m (Front axle)

5.8

Traction Control Lever

3.2

Traction Control Lever, Pump and Wheel Motors

2.3

Traction Pump

10.1

Transmission in first gear indicator light

4.2

Transmission in second gear indicator light

4.2

Transmission in third gear indicator light

4.2

Transmission neutral indicator light

4.2

Transport

2.5

Travelling on Public Roads

1.3

Travelling on Public Roads

5.9

Trip engine hours

4.4

TROUBLESHOOTING

Turn Signal, Lights and Horn Lever

3.1

Turning Machine Off with Rear Wheels Steered

5.4

Turning Radius

10.1

Turning the Controller On and Off

3.4

Two-wheel-steer mode indicator light

4.2

Tyre Maintenance

6.10

Содержание ROGATOR 418























































































Результаты поиска

Содержание ROGATOR 418

Отзывы:

Похожие инструкции для ROGATOR 418

Бренды по названию

Популярные бренды

AGCO ROGATOR 418, Руководство оператора

Результаты поиска

Содержание ROGATOR 418

Отзывы:

Похожие инструкции для ROGATOR 418

Бренды по названию

Популярные бренды