AFM STC-WSN300-2M Скачать руководство пользователя

Страница: 53 / 84

Maintenance 53

4510012 - REV F – 220621

Blowdown Procedure

Performing this blowdown procedure at least every day is an essential part of steam operation.

It is good preventive maintenance, increases Boiler life, and prevents the Boiler from

malfunctioning due to scale buildup. Blowdown removes most of the scale sediment but does

not remove it completely. Ideally, blowdown should be performed at the end of the working day.

For the first week of operation, two blowdowns per day to clean the inside of the Boiler are

strongly recommended.

ATTENTION:

Never leave the Boiler unattended during the blowdown procedure.

Needed to Perform Blowdown Procedure:

•

Heat-resistant Work Gloves

•

Safety Glasses/Goggles

To Perform Blowdown Procedure:

  Turn the Boiler Controller Power Switch off.
  Allow the Conveyor to move any remaining product out of the Tunnel.
  Turn the Conveyor Power Switch off
  Turn the System Main Power Switch off.

Boiler Controller

Power Switch

(Off)

System Main

Power Switch

(Off)

Conveyor

Power Switch

(Off)

AFM-4510012-00036-01

AFM-4510012-00040-01

AFM-4510012-00053-01

Содержание STC-WSN300-2M





















































































Результаты поиска

Содержание STC-WSN300-2M

Отзывы:

Похожие инструкции для STC-WSN300-2M

Бренды по названию

Популярные бренды

AFM STC-WSN300-2M, Руководство пользователя

Результаты поиска

Содержание STC-WSN300-2M

Отзывы:

Похожие инструкции для STC-WSN300-2M

Бренды по названию

Популярные бренды