Aerpro AMHJP2K Скачать руководство пользователя страница 9

Страница: 9 / 14

Aerpro AERA10

Radio Replacement Kit

for Jeep

Wrangler JL and Jeep Gladiator JT Vehicles

AMHJP2

Page 9

Section 3: Radio Unit Harness Connections and Preparation (cont.)

Part Three:

AERA10D

Display Connections

Step 2

Step 1

Route the display harness and

cable through the front opening of

the main radio module mounting

bracket.

Connect one end of the 8-pin display

power harness into the

8-pin port on the

ERA10D

radio

module, then connect the LVDS

display video cable into the LVDS

display port on the

AERA10D

radio

module. (Both of these cables are

provided in the

Aerpro

radio box.)

Part Four: Securing the Wire Harness

Step 2

Step 1

Secure each end of one backstrap

(included in the

AERA10D

radio

box) to the plastic eyelets on the

side radio module mounting

brackets, then use zipties to secure

the factory style

52-pin connector and the rest of

the

radio unit wiring to the back

strap.

(The unit should resemble

the image pictured when complete.)

Run a zip tie through the metal

eyelet on the connections side

of the

AERA10D

radio module,

then tighten it down around the

main wiring harness to secure

it in place tightly against the

radio module.

Содержание AMHJP2K















Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды

Aerpro AMHJP2K, Руководство пользователя

Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды