Aerpro AMHJP2K Скачать руководство пользователя страница 7

Страница: 7 / 14

Aerpro AERA10

Radio Replacement Kit

for Jeep

Wrangler JL and Jeep Gladiator JT Vehicles

AMHJP2

Page 7

Section 2: Radio Unit Mounting Preparation (cont.)

Section 3: Radio Unit Harness Connections and Preparation

Step 3

Step 2

Step 1

Connect the PL1 interface module

connector labeled “PAC LINK” into

the 3-pin port on the PAC-LINK

interface module.

AMPLIFIED

NON-AMPLIFIED

Connect the four CH4A-JW18

interface module connectors

into the appropriate ports on the

CH4A-JW18 interface module.

Ensure that the 12-pin connector

is plugged into the correct audio

output port (this depends on if the

vehicle is equipped with a factory

amplifier or not).

Connect the two

AERA10D

radio module connectors which

are labeled “16PIN RADIO”

and “10PIN RADIO” into the

appropriate ports on the

AERA10D

radio module.

Part One: Main Harness Connections (RPK-JW18-HAR)

Part Three: Assembling the Screen Mounting Panel

Step 2

Step 1

Lay the radio screen into the

mounting panel and secure it to

the panel using the four M4x12

screws included in your

AERA10D

kit

Install the six orange

retaining clips onto either the

AERA10D

mounting panel

Содержание AMHJP2K















Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды

Aerpro AMHJP2K, Руководство пользователя

Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды