Aerpro AMHJP2K Скачать руководство пользователя страница 12

Страница: 12 / 14

Aerpro AERA10

Radio Replacement Kit

for Jeep

Wrangler JL and Jeep Gladiator JT Vehicles

AMHJP2

Page 12

Section 4: In-Vehicle Harness Connections and Preparation (cont.)

Part Five: AM / FM Antenna Adapter and RPA-HD1

Step 2

Connect the factory camera cable

with an orange or red Fakra

connector into the Cam 1 port on

RPA-HD1, then slide the RPA-HD1

through the radio opening into the

cavity behind the dash that is above

the center left air vent or into the

cavity behind the right side of the

climate control mounting area.

Connect the AM/FM antenna

adapter (BAA22) to the antenna

with the white connector that was

disconnected from the factory

radio.

Step 1

Section 5: Radio Unit Installation

Step 2

Disconnect the two 4-pin

connectors on the RPK-

JW18-HAR, then connect the

MALE 4-pin connector on the

MQS4PT-36 harness into the

FEMALE 4-pin connector on the

RPK-JW18-HAR. The MALE

4-pin connector on the RPK-

JW18-HAR will no longer be

used.

Before attempting to mount the

radio unit into the dash, first

ensure that all excess cables and

wires are tucked into the sides,

out of the way of the radio. The

radio unit is a snug fit and will be

difficult to mount into the dash if

there is anything taking up space

behind the radio opening.

Step 1

Part One: Harness and Cabling Connections

Step 3

Connect the 2-pin chime speaker

connector to the main harness.

Note: You can also

place the RPA-HD1

into the cavity that

is below the radio

cavity behind the

climate control

panel on the right

side.

Содержание AMHJP2K















Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды

Aerpro AMHJP2K, Руководство пользователя

Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды