Aerpro AMHJP2K Скачать руководство пользователя страница 8

Страница: 8 / 14

Aerpro AERA10

Radio Replacement Kit

for Jeep

Wrangler JL and Jeep Gladiator JT Vehicles

AMHJP2

Page 8

Section 3: Radio Unit Harness Connections and Preparation (cont.)

Connect one end of the 18” harness

(10P-2-10P-18) into either of the two

10-pin PAC Link ports on the RPA-

HD1 interface module. The other

end will be connected to the open

10-pin port on the PL1 interface

module after mounting the radio unit

into the vehicle.

Connect one end of the 6”

harness (10P-2-10P-6) into the

10-pin expansion port on the

CH4A-JW18 interface module,

then connect the other end into

either of the two 10-pin ports on

the PL1 interface module.

Part Two: 10P-2-10P Harness and HDMI Connections

Part One: Main Harness Connections (RPK-JW18-HAR) (cont.)

Step 5

Step 4

Connect the white and red male

RCAs labeled “OEM AUX AUDIO”

on the RPK-JW18-HAR into the

white and red female RCAs

labeled “LINE IN / AUX IN” on the

A/V

Aerpro

RCA harness.

Connect the 24-pin A/V

Aerpro

RCA harness (provided in the

AERA10D

radio box) into the

24-pin port on the

Aerpro

radio

module.

Step 6

Connect the 6-pin SWI / IR harness

(provided in the

AERA10D

radio box)

into the 6-pin port on the

Aerpro

radio

module, then connect the 3.5mm jack

labeled “STEERING WHEEL

CONTROL” on the RPK-JW18-HAR

into the female 3.5mm connector

labeled “SWI” on the

Aerpro

SWI / IR

harness.

Connect one end of the 12” HDMI

cable into the HD OUT port on the

HD1 interface module. The other

end will be connected to the

HDMI input port on the

ERA10D

module after mounting the HD1

interface module into the vehicle.

Step 1

Prior to making connections to the RPA-HD1 module,

verify that all 4 of the module’s DIP Switches are set to the

up position (OFF).

DIP SWITCHES LOCATED ON TOP

SIDE OF MODULE

Step 2

Step 3

Содержание AMHJP2K















Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды

Aerpro AMHJP2K, Руководство пользователя

Результаты поиска

Содержание AMHJP2K

Отзывы:

Бренды по названию

Популярные бренды